Bluetooth: RFCOMM: connect the session socket without rfcomm_mutex

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: connect the session socket without rfcomm_mutex An RFCOMM connect() issued while a BR/EDR link is being authenticated makes lockdep report a circular dependency, and the reported cycle is a real AB/BA between rfcomm_mutex and hdev->lock. rfcomm_security_cfm() is called from the HCI event path, which already holds hdev->lock: hci_rx_work() hci_event_packet() hci_cc_read_enc_key_size() [hdev->lock] hci_encrypt_cfm() [hci_cb_list_lock] rfcomm_security_cfm() [rfcomm_mutex] while an RFCOMM connect() from userspace takes the same two locks the other way round: rfcomm_sock_connect() rfcomm_dlc_open() [rfcomm_mutex] __rfcomm_dlc_open() rfcomm_session_create() kernel_connect() l2cap_sock_connect() l2cap_chan_connect() [hdev->lock] WARNING: possible circular locking dependency detected kworker/u131:1/1128 is trying to acquire lock: rfcomm_mutex, at: rfcomm_security_cfm+0x31/0x3e0 [rfcomm] but task is already holding lock: hci_cb_list_lock, at: hci_cc_read_enc_key_size+0x1d2/0xcc0 Chain exists of: rfcomm_mutex --> &hdev->lock --> hci_cb_list_lock hci_auth_complete_evt() and hci_encrypt_change_evt() reach the callback the same way. Both orders have to be seen in the same boot, which is why a BR/EDR connection alone is not enough to show it: a session set up by the remote side is created by rfcomm_accept_connection() in krfcommd, which calls kernel_accept() and never takes hdev->lock under rfcomm_mutex. Connecting a device that authenticates and encrypts the link and then calling connect() on an RFCOMM socket towards any address - the connect does not have to succeed, the order is recorded before the page timeout - reports it every time. Only the session socket has to be connected with the lock held, and it does not: nothing else can see the socket before it is put on the session list. So connect it first and take rfcomm_mutex afterwards, which removes the rfcomm_mutex -> hdev->lock order for good, rather than keeping the HCI event path out of rfcomm_mutex. rfcomm_session_create() becomes rfcomm_session_connect(), which returns the connected socket without touching the session list, and rfcomm_dlc_open() adds the session once it holds the lock again. If another opener added a session for the same pair while this socket was connecting, that session is used and this socket is dropped. __rfcomm_dlc_open() now takes the session it should use, and its state check runs after the lock is re-acquired, so a DLC that was opened or closed in the meantime is still handled. Over an existing ACL link the connection can complete before the session reaches the list, and the wakeup from the socket callback is then lost, so krfcommd is woken once the session is visible. Connecting without the lock opens a window in which the socket can be closed. The DLC is not on a session yet, so rfcomm_dlc_close() finds nothing to do and returns without touching it, and rfcomm_dlc_open() would then attach a DLC whose owner is gone. rfcomm_dlc_close() now marks such a DLC with RFCOMM_CLOSED, and rfcomm_dlc_open() checks the mark once it holds rfcomm_mutex again and drops the socket instead of attaching the DLC. The mark is cleared when an open starts, so a DLC that is reused is not affected. This covers both callers of rfcomm_dlc_open(), the socket and the tty layer.

Source published

23 Oct 2026 12:20:34 UTC

Source modified

23 Oct 2026 12:20:34 UTC

Observed here

23 Oct 2026 16:01:20 UTC

Source terms

CVE Program Terms of Use

Original source record · Cite this exact observation · Complete original publisher JSON

This view projects the publisher's source fields for reading; the original JSON retains additional fields and CVE enrichment containers. Attribution: cve-program · CVE Program Terms of Use. Source text is retained; field grouping and change labels are provided by ChangeIntel.