Public mode

No access to your tenant or devices. Every item links to its source. What this means

Sources need attention Customize Public modeDiscuss ChangeIntel on Discord

net: thunderbolt: Tear down DMA paths before stopping the rings

CVSS 3.1 8.8 HIGHCheck source for fixed versionsKEV status unknown

Historical advisory recorded 23 Oct 2026 15:48:27 UTC. Read the latest advisory.

cve-program · CVE-2026-74691

Published

In the Linux kernel, the following vulnerability has been resolved: net: thunderbolt: Tear down DMA paths before stopping the rings tbnet_tear_down() stops both rings and frees their frame buffers before calling tb_xdomain_disable_paths(). tb_ring_stop() zeroes the ring's descriptor base and tbnet_free_buffers() unmaps and frees the pages the frames sit in, so by the time __tb_path_deactivate_hop() polls the hop's 'pending' bit, anything still in flight has nowhere to drain to. The teardown sequence has been in this order since the driver was added. The setup path has not: commit ff7cd07f3064 ("net: thunderbolt: Enable DMA paths only after rings are enabled") moved the path enable to the end of tbnet_connected_work() and documented why: /* Both logins successful so enable the rings, high-speed DMA * paths and start the network device queue. * * Note we enable the DMA paths last to make sure we have primed * the Rx ring before any incoming packets are allowed to * arrive. */ Teardown was never updated to match, so the rings and the paths now come down in the same order they go up instead of in reverse. On an ASMedia ASM4242 host router the 'pending' bit then never clears: every teardown burns the full 500 ms timeout and __tb_path_deactivate_hop() returns -ETIMEDOUT. Raising the timeout to 5 s does not help, so the hop is not slow to drain, it never drains at all. The failure is invisible above the thunderbolt core. __tb_path_deactivate_hops() is void and only calls tb_port_warn(); tb_path_deactivate(), tb_tunnel_deactivate() and __tb_disconnect_xdomain_paths() are void as well, and tb_disconnect_xdomain_paths() ends in an unconditional "return 0". So tb_xdomain_disable_paths() reports success and the netdev_warn() below it never fires. Repeated teardowns eventually take the XDomain control channel down, after which the peer node is gone and only a power cycle brings the controller back. Deactivating the paths first fixes it. Measured with kretprobes on a stock v6.17 tree with no other patches applied, on a link that was up and had just carried traffic: before: __tb_path_deactivate_hop() returns 0 for the first hop, then -ETIMEDOUT for the second 500335 us later after: 0 for both, 525 us apart Alternating the two orderings ABBA over three load levels, four teardowns per arm: every teardown failed before the change (21 of 21 that ran), none failed after (0 of 24). The before arms ran short because the link died partway through. The same split shows up when the interface is enslaved to a bond instead of just brought down, which is how I ran into this in the first place. Throughput and latency after the change are unchanged. Hosts whose routers drain the hop despite the stale descriptor base see no functional difference, since the paths end up deactivated either way.

Read the publisher's advisory

Affected versions, risk and source history

cve-program · CVE-2026-74691

Published

net: thunderbolt: Tear down DMA paths before stopping the rings

In the Linux kernel, the following vulnerability has been resolved: net: thunderbolt: Tear down DMA paths before stopping the rings tbnet_tear_down() stops both rings and frees their frame buffers before calling tb_xdomain_disable_paths(). tb_ring_stop() zeroes the ring's descriptor base and tbnet_free_buffers() unmaps and frees the pages the frames sit in, so by the time __tb_path_deactivate_hop() polls the hop's 'pending' bit, anything still in flight has nowhere to drain to. The teardown sequence has been in this order since the driver was added. The setup path has not: commit ff7cd07f3064 ("net: thunderbolt: Enable DMA paths only after rings are enabled") moved the path enable to the end of tbnet_connected_work() and documented why: /* Both logins successful so enable the rings, high-speed DMA * paths and start the network device queue. * * Note we enable the DMA paths last to make sure we have primed * the Rx ring before any incoming packets are allowed to * arrive. */ Teardown was never updated to match, so the rings and the paths now come down in the same order they go up instead of in reverse. On an ASMedia ASM4242 host router the 'pending' bit then never clears: every teardown burns the full 500 ms timeout and __tb_path_deactivate_hop() returns -ETIMEDOUT. Raising the timeout to 5 s does not help, so the hop is not slow to drain, it never drains at all. The failure is invisible above the thunderbolt core. __tb_path_deactivate_hops() is void and only calls tb_port_warn(); tb_path_deactivate(), tb_tunnel_deactivate() and __tb_disconnect_xdomain_paths() are void as well, and tb_disconnect_xdomain_paths() ends in an unconditional "return 0". So tb_xdomain_disable_paths() reports success and the netdev_warn() below it never fires. Repeated teardowns eventually take the XDomain control channel down, after which the peer node is gone and only a power cycle brings the controller back. Deactivating the paths first fixes it. Measured with kretprobes on a stock v6.17 tree with no other patches applied, on a link that was up and had just carried traffic: before: __tb_path_deactivate_hop() returns 0 for the first hop, then -ETIMEDOUT for the second 500335 us later after: 0 for both, 525 us apart Alternating the two orderings ABBA over three load levels, four teardowns per arm: every teardown failed before the change (21 of 21 that ran), none failed after (0 of 24). The before arms ran short because the link died partway through. The same split shows up when the interface is enslaved to a bond instead of just brought down, which is how I ran into this in the first place. Throughput and latency after the change are unchanged. Hosts whose routers drain the hop despite the stale descriptor base see no functional difference, since the paths end up deactivated either way.

Source published
22 Aug 2026 15:32:55 UTC
Source modified
25 Aug 2026 05:41:36 UTC
Saved here
23 Oct 2026 15:48:27 UTC
Source terms
CVE Program Terms of Use

Original source record · Cite this exact observation · Complete original publisher JSON

Source: cve-program · CVE Program Terms of Use. The publisher's wording is preserved. ChangeIntel groups the information and labels changes. The JSON record includes additional source fields.

CVSS 3.1 · 8.8 CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H

ChangeIntel

An IT change radar: releases, security, known issues, retirements, documentation changes, and service status from public sources. Every item links to supporting evidence; dates and statuses can change after they are read.

Sources read 21 Nov 15:36 UTC · 273 of 275 readable · 269 fully read · documentation 469/469 current