Public mode

No access to your tenant or devices. Every item links to its source. What this means

Sources need attention Customize Public modeDiscuss ChangeIntel on Discord

spi: spi-qpic-snand: write the feature value before executing SET_FEATURE

CVSS 3.1 8.4 HIGHCheck source for fixed versionsKEV status unknown

cve-program · CVE-2026-80712

Published

In the Linux kernel, the following vulnerability has been resolved: spi: spi-qpic-snand: write the feature value before executing SET_FEATURE qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits the descriptors, which makes the controller execute the command immediately. For SPINAND_SET_FEATURE the value to be written is only placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a second submission - so the chip is programmed with whatever that register happened to hold from a previous operation, and the intended value is only applied by the *next* SET_FEATURE. Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing 0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the subsequent write of 0x00 leaves it at 0x40 - every write lands one operation late. This stayed unnoticed until v6.18 added SPI-NAND OTP support together with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode, reads, and disables it again, and mtd_otp_nvmem_add() does this during MTD registration. With the off-by-one, the "disable" write actually applies the previously requested value, so CFG_OTP_ENABLE ends up set: the chip stays in OTP mode, every subsequent array read returns the OTP area instead of the array (UBI reports an empty device) and all writes fail with -EIO because the OTP area is write protected. On this board that makes the whole flash unusable and the device unbootable. Write the feature value into NAND_FLASH_FEATURES as part of the same transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the operation actually carries - the previous code dereferenced a 4-byte pointer on a one-byte buffer (spinand->scratchbuf). With this patch the flash contents read back bit-identical to a known-good dump of the same board taken under the vendor firmware (md5-verified across partitions), and writes work.

Read the publisher's advisory

Affected versions, risk and source history

Exploitation and risk

Source status

CISA KEV lists vulnerabilities known to be exploited. FIRST EPSS estimates the likelihood of exploitation in the next 30 days. An unavailable score does not mean zero risk.

Which CVEs have scores here?

This view includes predictions for CVE identifiers explicitly listed in public NuGet advisories. Microsoft release pages have their own prediction coverage. Check source status for the scope and latest checks.

No exploitation or prediction data is available here for these CVEs. This does not mean they are safe or unlikely to be exploited.

cve-program · CVE-2026-80712

Published

spi: spi-qpic-snand: write the feature value before executing SET_FEATURE

In the Linux kernel, the following vulnerability has been resolved: spi: spi-qpic-snand: write the feature value before executing SET_FEATURE qcom_spi_send_cmdaddr() programs NAND_FLASH_CMD/NAND_EXEC_CMD and submits the descriptors, which makes the controller execute the command immediately. For SPINAND_SET_FEATURE the value to be written is only placed into NAND_FLASH_FEATURES afterwards, by qcom_spi_io_op(), in a second submission - so the chip is programmed with whatever that register happened to hold from a previous operation, and the intended value is only applied by the *next* SET_FEATURE. Measured on a TP-Link Archer AX55 v1 (IPQ5018, ESMT F50L1G41LB): writing 0x40 to the configuration register (0xb0) leaves the chip at 0x00, and the subsequent write of 0x00 leaves it at 0x40 - every write lands one operation late. This stayed unnoticed until v6.18 added SPI-NAND OTP support together with OTP entries for ESMT chips. spinand_otp_rw() enables OTP mode, reads, and disables it again, and mtd_otp_nvmem_add() does this during MTD registration. With the off-by-one, the "disable" write actually applies the previously requested value, so CFG_OTP_ENABLE ends up set: the chip stays in OTP mode, every subsequent array read returns the OTP area instead of the array (UBI reports an empty device) and all writes fail with -EIO because the OTP area is write protected. On this board that makes the whole flash unusable and the device unbootable. Write the feature value into NAND_FLASH_FEATURES as part of the same transaction, before NAND_EXEC_CMD. While at it, copy only the bytes the operation actually carries - the previous code dereferenced a 4-byte pointer on a one-byte buffer (spinand->scratchbuf). With this patch the flash contents read back bit-identical to a known-good dump of the same board taken under the vendor firmware (md5-verified across partitions), and writes work.

Source published
28 Aug 2026 06:53:11 UTC
Source modified
29 Aug 2026 06:22:28 UTC
Saved here
23 Oct 2026 15:48:27 UTC
Source terms
CVE Program Terms of Use

Original source record · Cite this exact observation · Complete original publisher JSON

Source: cve-program · CVE Program Terms of Use. The publisher's wording is preserved. ChangeIntel groups the information and labels changes. The JSON record includes additional source fields.

CVSS 3.1 · 8.4 CVSS:3.1/AV:L/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H

ChangeIntel

An IT change radar: releases, security, known issues, retirements, documentation changes, and service status from public sources. Every item links to supporting evidence; dates and statuses can change after they are read.

Sources read 20 Nov 05:45 UTC · 268 of 275 readable · 264 fully read · documentation 469/469 current